Recent Activity

Activity stream for all registered members at Shamrock Boat Owners' Club.

  1. Satraker liked Bestday's post in the thread Planning on Buying ‘99 246 Open.

    Bought the same boat last August from a gentleman in Boston. Very similar scenario- original owner very low hours at 328. I however...

    Jan 22, 2021 at 11:12 PM
  2. Bestday replied to the thread Planning on Buying ‘99 246 Open.

    Bought the same boat last August from a gentleman in Boston. Very similar scenario- original owner very low hours at 328. I however...

    Jan 22, 2021 at 10:35 PM
  3. Satraker attached a file to the thread Planning on Buying ‘99 246 Open.

    She’s mine now! Tranny was a Brother in Law issue... he took it out and said it stopped on him. Perhaps he mistook the shifter for the...

    9F364CE2-EBED-4418-90FE-5C5E4D7C6977.jpeg 68FB427D-67E9-4195-97C0-C3B91AD51E52.jpeg Jan 22, 2021 at 8:08 PM
  4. ftu209 liked Donald F Learn's post in the thread Shamrock website and forum changes.

    Hey everyone, sorry ahead of time for the long post. We've got some important changes coming up that everyone needs to know about....

    Jan 22, 2021 at 7:39 PM
  5. Mickey Z attached a file to the thread Help.

    the risers for my engine (Osco) Is there a gasket for these? When I took them off there was no gaskets. Just form a gasket type stuff....

    1.jpg front deck.jpg IMG_0288.JPG transom 2.jpg transom painted.jpg Jan 22, 2021 at 7:03 PM
  6. HookedUp330 replied to the thread 5.7 crusader mpi.

    Anyone repower a 246wa from a 5.7mpi to a 6.0 or a 6.2? If so what have you gained speed, fuel mileage, is it worth the extra money for...

    Jan 22, 2021 at 3:13 PM
  7. HookedUp330 replied to the thread 5.7 crusader mpi.

    Ok had a few minutes today to dig deeper into this. Yes fcc filter changed. Dont know fuel pressure haven't checked that yet. But while...

    Jan 22, 2021 at 2:45 PM
  8. mako2 liked Donald F Learn's post in the thread Shamrock website and forum changes.

    Hey everyone, sorry ahead of time for the long post. We've got some important changes coming up that everyone needs to know about....

    Jan 22, 2021 at 2:13 PM
  9. Gary S replied to the thread 5.7 crusader mpi.

    Since you might be waiting awhile to get the codes read you could get yourself a fuel pressure tester at HF get the specs for that...

    Jan 22, 2021 at 1:02 PM
  10. redneck liked 17'shammy's post in the thread Fuel Tank Replacement 17 Footer.

    cont. Re-sealed the Cap to Hull joint (used Sikaflex 291) [ATTACH] [ATTACH] Re-installing the Rub Rail [ATTACH] [ATTACH] Deciding...

    Re-Caulking-Deck-To-Hull-_-20210118_121124.jpg Installing-Rub-Rail-_-20210120_111855.jpg Rub-Rail-Re-installed-_-20210120_132109.jpg Sikaflex-291_2_20210119_100820.jpg Jan 22, 2021 at 1:00 PM
  11. redneck liked 17'shammy's post in the thread Fuel Tank Replacement 17 Footer.

    Still waiting on the new tank ... Soooo ... While waiting I decided to pull the Rub Rail [ATTACH] [ATTACH] I cleaned up the 33 year old...

    Removing-Rub-Rail-_-20210101_105606.jpg Rub-Rail-Removed-_-20210101_133310.jpg Ready to Lift-_-20210105_141444.jpg Cap-Lifted-_-20210106_120646.jpg Old-Plywood-Receiver-Strip-_-20210106_120724.jpg PVC-Receiver-Strip-_-20210107_141856.jpg Liner-to-Hull-Joint-_-20210106_142231.jpg Liner-to-Hull-Butyl-_-20210108_132631.jpg Cap-Back-Down-_-20210108_143708.jpg Jan 22, 2021 at 12:59 PM
  12. redneck replied to the thread Planning on Buying ‘99 246 Open.

    Looks clean, The trailer could be setup to fit the boat better. Why were the valves adjusted? I would think they would be hydraulic....

    Jan 22, 2021 at 12:58 PM
  13. redneck replied to the thread 5.7 crusader mpi.

    Is it going into limp mode because the ECM see's the engine/elbows are over heating? The sensor that runs your gauge is different from...

    Jan 22, 2021 at 12:48 PM
  14. Holty replied to the thread Planning on Buying ‘99 246 Open.

    I would ask a surveyor that question.

    Jan 22, 2021 at 12:38 PM
  15. radioman replied to the thread 5.7 crusader mpi.

    ECM might be sensing a fuel pressure problem. Did you change the filter in the FCC?

    Jan 22, 2021 at 11:47 AM
Loading...